|Year : 2017 | Volume
| Issue : 3 | Page : 192-198
Eco-friendly coloration of silk and flax fabrics with natural dye enhanced by ultraviolet radiation
Heba M El-Hennawi, Safia A Mahmoud, Amira A Ragheb
Dyeing Printing and Auxiliaries Department, Textile Division, National Research Centre, Giza, Egypt
|Date of Submission||04-Oct-2017|
|Date of Acceptance||19-Oct-2017|
|Date of Web Publication||26-Dec-2017|
Heba M El-Hennawi
Dyeing Printing and Auxiliaries Department, Textile Division, National Research Centre, Dokki 12311, Giza
Source of Support: None, Conflict of Interest: None
Background and objectives Plants are the main source of natural colorant as they are widely available and can be considered as zero cost dyes, as they are obtained from plants planted for other purposes. All the parts of plants are used for extracting natural color, and most of them have antimicrobial and antifungal values. The importance using of natural dye is not restricted only to its antimicrobial or other medicine value but also to its global benefit through elimination of environmental pollution, caused by usage of synthetic dyes. The disadvantage of coloring fabric with natural dye is its fastener properties, as natural dye has no affinity to the fabric.
The objective of the present work is to produce an eco-friendly colored fabric produced through use of safe materials (no dyeing salts or mordant) with the aid of ultraviolet (UV) radiation. The coloring component from Chelidonium majus was extracted using boiling water, and examination was done on its coloration effect on flax and silk fabrics before and after being exposed to UV radiation for both extracted dye and fabrics.
Materials and methods Natural dye from UV-irradiated powder of C. majus was extracted using boiling water. The dye was used in coloration of flax and silk fabrics through dyeing process and screen printing. The effect of irradiated treatment time, dyeing bath conditions (time and temperature) as well as fixation type of printed samples has been studied. The effect of UV radiation on the morphology structure of both fabrics was illustrated by scanning electron microscope.
Results and conclusion UV radiation improved the color strength (K/S) and fastness properties for both colored fabrics either dyed or printed. The optimum dyeing bath conditions used for silk and flax samples were 30°C for 30 min and 90°C for 1 h, respectively. The printed silk samples fixed by thermofixation and printed flax samples fixed using steamer have given better color strength. All dyed samples have antimicrobial properties.
Keywords: antimicrobial, Chelidonium majus, flax fabric, silk fabric, ultraviolet radiation
|How to cite this article:|
El-Hennawi HM, Mahmoud SA, Ragheb AA. Eco-friendly coloration of silk and flax fabrics with natural dye enhanced by ultraviolet radiation. Egypt Pharmaceut J 2017;16:192-8
|How to cite this URL:|
El-Hennawi HM, Mahmoud SA, Ragheb AA. Eco-friendly coloration of silk and flax fabrics with natural dye enhanced by ultraviolet radiation. Egypt Pharmaceut J [serial online] 2017 [cited 2020 Nov 24];16:192-8. Available from: http://www.epj.eg.net/text.asp?2017/16/3/192/221488
| Introduction|| |
Since the past decade, there has been a revival in the world to get back to all natural products (dye and fabric) owing to international awareness to environment and ecology preservation. Among the nature fabrics, flax and silk have gained attention owing to their properties. Flax like cotton is a cellulose polymer but has the freshness, comfort, and elegance of linen clothing. The crystalline structure of flax makes it stronger but with poor dyeing ability owing to the low penetration of dye molecules into the fiber ,. To go beyond this problem, a number of modifications by cationic agent or polymer grafting have been carried out to improve the dye uptake and overall fastness properties ,. Silk is the highest priced among all natural fabrics owing to its properties such as washability and wearability; however, its dye ability and color fastness properties are weak, and they should be improved. For this purpose, surface modification of silk by some physical and chemical techniques has been suggested .
Chelidonium majus belongs to Papaveracecae family and is broadly distributed across the world, as it is found in Europe, Asia, Northwest Africa, and North America. C. majus is known under different names, and more than 20 different Chelidonium alkaloids have been identified. The different groups of chemical molecules that are present in the herb of C. majus are as follows: benzylisoquinoline type (0.01–1); acids such as chelidonic, malic, citric, caffeic (0.4%) ferulic (0.02%), and p-coumaric (0.06%); and others such as flavonoids .
Physical treatments such as plasma and ultraviolet (UV) radiation are dry and clean processes, which make them good alternative to wet treatment. There are several types of radiations. However, UV radiation constitutes 5% of the total incident sunlight on earth surface (visible light 50% and IR radiation 45%). Even though its proportion is quite less, it has the highest quantum energy compared with other radiations . Recently researchers carried out work on the effect of UV radiation on dyeing of cotton with reactive and nature dyes. The irradiation of fibers with UV increases the wet ability of cotton which improves the color shade and fastness properties ,.
This research studies the effect of UV radiation on both flax and silk fabric morphologies to improve their dyeing and printing ability with aqueous extracted natural dye of C. majus without addition of any mordant or salts. Different conditions of UV radiation treatment of silk and flax were studied, subjected to different dyeing bath conditions (time and temperature). The irradiated fabrics were printed using irradiated dye and subject to fixation by either steaming or thermofixation.
| Materials and methods|| |
Nature coloring matter
Coloring substance used in this work was extracted from Chelidonium plants.
Silk and flax fabrics, mill scoured and bleached, were kindly supplied by Misr El-Beida Dyers Company (Kafr El-Dawar, Alexandria, Egypt).
UV radiation (245 nm, 180 W) was used for irradiating dye powder, silk, and flax fabrics for different time interval.
Extraction of the natural coloring matter
C. majus ([Figure 1]) were crushed to the powder form, and the coloring matter was extracted using 1–5 g of the powder in 100 ml of water at the boil for 1 h. At the end, the solution was filtered off and left to cool down.
Fabric samples were dyed with the natural coloring matter extracted from C. majus at liquor ratio 1 : 40. Dyeing was carried out at pH 3–10. To observe the effect of dyeing time and temperature, the dyeing process was carried out at different period of time (20, 30, 40, 50, 60, and 70 min) and temperature (20–100°C). The effect of dye concentration was studied at 1, 2, 3, 4, and 5% of dye solution. The dyed samples were rinsed with cold water and washed for 30 min in a bath containing 3 g/l of nonionic detergent at 45°C. Finally, the fabrics were rinsed and air dried.
The UV-irradiated fabrics were printed by silk screen technique, and the fabrics samples were fixed by steaming and/or thermofixation.
Preparation of printing paste
The printing pastes were set by adding 3 g of the dye to 50 g of thickener suspension, and then the total weight of the whole paste were adjusted to 100 g. Thickener suspension was prepared by soaking 3 g of sodium alginate in little amount of water overnight at room temperature. All the printed samples were fixed by two different ways: thermofixation at 160°C for 10 min and steaming at 100°C for 15 min. The fixed samples were washed with cold running water, soaping (using 2 g/l nonionic detergent) at 45°C for 15 min, and at last, rinsing with cold water. After drying, the printed fabrics were assessed for color strength value (K/S) and overall fastness properties.
Analysis and measurements
The color strength (K/S) and Lab values was measured by reflection spectroscopy with a Hunter Lab UltraScan PRO (USA, 2007) spectrophotometer according to a standard method .
Tensile strength of fabric
The test was carried out according to the ASTM Standard Test method D 682 1924 on a tensile strength apparatus type FMCW 500 (VebThuringer Industries Work, Rauenstein, Germany) at 25±2°C and 60±2% relative humidity .
Morphology of the fabrics by scanning electron microscope
The untreated and treated fabrics were analyzed by scanning electron microscope (SEM), Topcon-Microscope (ATB-55), to investigate morphological changes of the surface structure.
The dyed samples were subjected to rubbing, washing, perspiration, and light according AATCC test methods .
The microorganisms used were ATCC registered strains, except Bacillus cereus, which was a local isolate obtained from Agriculture Microbiology Department, National Research Centre, Egypt. The following microorganisms were included as test microorganisms: Streptococcus pyogenes (19 615), Escherichia More Details coli (25 922), and Aspergillus niger (6275).
| Results and discussion|| |
Effect of ultraviole radiation time on fabric
The used fabrics (silk and flax) were exposed to UV radiation from 10 to 70 min, and dyed with the native dye powder for 30 min, 3% weight of fabric (w.o.f.) at pH 8 and liquor ratio (L.R) 1: 40. Dyeing was continued for 60 min at 100°C. [Figure 2] show that irradiating fabrics exhibited better color strength (K/S) than nonirradiating fabric at all irradiation time regardless of the fabric type. However, the dyed silk samples had higher K/S, as its light weight makes its surface more affected by the UV rays. UV radiation increases the dye uptake by two ways: the oxidation process of cellulosic fabric, as the OH moieties of cellulose oxidize to carboxylic acid, which have more affinity to dye, and the photomodification of the fabric surface ,. As can be seen from [Figure 2], the maximum color strength value was obtained at UV radiation for 30 min for silk and 60 min for flax.
|Figure 2 Effect of different UV radiation times of silk and flax fabric on K/S value of fabric dyeing, at pH 8, 3% (w. o. f.), 100°C, for 60 min and irradiation of the dye for 1 h. UV, ultraviolet.|
Click here to view
Effect of ultraviole radiation time on dye powder
The extracted color product from C. majus in aqueous solution was dried and exposed to UV radiation for different time (20–80 min). The dyeing bath of UV-treated fabric (silk for 30 min and flax for 60 min) was subjected to dyeing conditions of pH 8, 3% (w. o. f.), and L.R 1 : 40. Dyeing was continued for 60 min at 100°C. The color strength (K/S) values of dyed washed samples were plotted in [Figure 3]. The maximum color strength (K/S) value was obtained at 30 min of UV radiation for both silk and flax. Moreover, we can see that by increasing dye radiation time from 40 to 80 min, the color strength value decreased. UV radiation acts as a catalyst in the oxidation reaction of organic materials in the atmospheric air, forming peroxides from tannins and oils; this increases the coloring matters to some extent, but further radiation time could cause hydrolysis .
|Figure 3 Effect of different UV radiation time of dye on K/S value of silk and flax fabrics. UV, ultraviolet.|
Click here to view
Effect of pH
To study the effect of pH on the dye uptake and color strength (K/S), the dyeing bath was set at different pH from 3 to 10 for dyeing the treated fabrics using irradiated dye powder at optimum UV radiation time. [Figure 4] showed that the maximum color strength value was obtained at pH 9 which is a strong alkaline medium, whereas the lowest value can be observed at acid medium of pH 3.
|Figure 4 Effect of different pH on K/S value of silk fabric dyeing at 100°C, 3% (w. o. f.), for 60 min, with fabric irradiation for 30 min and dye irradiation for 30 min.|
Click here to view
Effect of different dyeing temperature
To study the effect of UV treatment of both fabric and dye powder on dyeing conditions such as temperature, the dyeing bath containing the irradiated fabric and dye powder at pH 9 was subjected to 20–100°C for 60 min. [Figure 5] showed that UV radiation decreased the dyeing bath temperature for both fabrics. The optimum temperature of silk dyeing bath temperature was 30°C, which is low compared with conventional temperature, which reaches 100°C . Recent research on silk dyeing using corona discharge and chitosan pretreatment stated that the dyeing temperature was 60°C, which is relatively high . On the contrary, the optimum temperature of dyeing bath for flax was at 90°C, and this difference could be attributed to the nature of the fiber.
|Figure 5 Effect of different dyeing temperatures on K/S value of silk fabric dyeing at pH 9, 3% (w. o. f.), 100°C, for 60 min, with fabric irradiation for 30 min and dye irradiation for 30 min.|
Click here to view
Effect of different dyeing time
The effect of dyeing time is as important as the effect of dyeing temperature, which was also studied. Treated fabrics and dye powder at optimum radiation were used at different time intervals (20–70 min) at pH 9 and at 30°C for silk and 90°C for flax fabric.
[Figure 6] shows that increasing dyeing time from 20 to 70 min leads to increase in K/S value as the color gets adsorbed then absorbed on the fabric surface. Further increase in the dyeing time after 30 and 60 min for silk and flax, respectively, has no significant effect on the color absorbance, as reflected in the K/S values. This points to an equilibrium between the dye molecule adsorb to fabric surface and that which leaves to the dye bath, and this differ according to the fabric type (henna).
|Figure 6 Effect of different dyeing time on K/S value of silk fabric dyeing at pH 9, 3% (w. o. f.), 30°C, with fabric radiation for 30 min and dye radiation for 30 min.|
Click here to view
[Figure 6] shows that optimum dyeing time for silk and flax fabrics was obtained at 30 and 60 min, respectively.
Effect of different dye concentration
The irradiated fabrics (flax for 60 min and silk for 30 min) were dyed with irradiated dye (for 30 min) at pH 9. Dyeing was continued for 30 min at 30°C in case of silk fabric, whereas 60 min at 90°C for flax fabric. [Figure 7] show that as the dye concentration increases from 1 to 4%, the color strength also increases. Above the 4% dye concentration, the color strength values nearly leveled off or a very slight improvement took place.
|Figure 7 Effect of different dye concentrations on K/S value of silk fabric dyeing at conditions of pH 9, 30°C, for 20 min, with fabric IR-radiation for 30 min and dye irradiation for 30 min.|
Click here to view
Scanning electron microscope study of fabric
The effect of UV radiation on the morphology structure of both silk and flax fabrics is shown in the [Figure 8]. Silk fibers’ backbone is fibroin, which is a highly crystalline fibrous protein, and the sericin, which constitutes ∼30% in weight; however, all of sericin should be removed from the silk fibers before coloring . [Figure 8] shows the surface structure of untreated silk, and the presence of residual sericin covering the fiber filament is noted, and the surface is smooth with no cracks or pits. [Figure 8] illustrate that after UV irradiation, the silk surface is clean, and we notice the appearance of nodes and cracks in the direction of filament axes, where the absorbance of water occurs, and that dyes and finishing agents often accumulate there . Moreover, the filament compactness of the fabric increases the surface area pores allows the penetration of dye into the fiber core enhancing the color strength and rate of fastness properties. Multicellular flax fibers are connected to each other by pectin, and the outer surface of fibers consists of pectin, lignin, and waxy materials. As seen in the SEM image of untreated fibers ([Figure 9]), the outer surface of the fiber filament is covered with impurities (noncellulosic materials), and there are almost no spaces present, which decreases its wettability. The photomodification by UV radiation cleaned the surface and made the fiber filaments creating more spaces where more dye could be accumulated, and as a result the interaction for dyeing flax fiber becomes more significant ([Figure 9]).
|Figure 8 SEM of untreated and UV-treated silk fabric. SEM, scanning electron microscope; UV, ultraviolet.|
Click here to view
|Figure 9 SEM of untreated and UV-treated flax fabric. SEM, scanning electron microscope; UV, ultraviolet.|
Click here to view
The irradiated printed fabric were printed with paste containing irradiated natural dye and fixed with steaming for 30 min and/or thermofixation at 150°C for 5 min. Parallel steps were applied by using untreated fabric and dye for comparison study. The fixation step is essential to the printed fabrics to have almost completely fixed dye before washing any default in this step has a dramatically effect on the samples. The type of fixation depends on the nature of fabric and dye. [Table 1] shows that for the printed silk samples fixation by thermofixation is more suitable as the K/S raise from 8.19 to 12.73 for treated sample, and a value is positive point to that the sample has reddish yellow hue. As for flax printed samples, the steaming fixation of samples gave higher K/S (11.52) for irradiated samples whereas it was 5.93 by thermofixation. The steamer provides the heat and moisture necessary to swell the flax fiber and for dye diffusion to the fiber surface.
Evaluation of colored samples
The results for color fastness to light, washing, and rubbing are given in [Table 2]. It is revealed that under optimum conditions of temperature, time, and pH, irradiated flax and silk fabrics dyed with irradiated natural dye have good color fastness properties. The upgrading of fastness properties are because of the presence of benzene rings in dye molecules which show more affinity toward irradiated fabric and resistance toward factors such as detergent, heat, light, and rubbing . The results shown in [Table 2] regarding color fastness properties confirmed that UV irradiation had the ability to modify the surface of the fabric, which could improve the fastness properties.
The UV radiation effect on the surface morphology of silk and flax fabrics, as is proved in the scan figures ,, becomes important through the measurement of tensile strength. The tensile strength of silk increases owing to the compactness of filament, whereas in flax, the tensile strength slightly decreases owing to filament swelling ([Table 3]).
The results presented in [Table 2] show that the most potent antimicrobial effect was viewed by irradiated silk printed sample, represented by 42 mm as axial zone of inhibition against S. pyogenes followed by its blank, whereas for flax irradiated and blank samples, 23 and 17 mm as axial zones of inhibition against S. pyogenes, respectively, were seen. On the contrary, the antifungal effects against A. niger were showed by all the samples; the highest effect was given by the irradiated samples of either flax or silk giving 17 and 16 mm as axial zones of inhibition, respectively. The same phenomena was noticed with the antibacterial effect against E. coli by 18 and 17 mm as axial zones of inhibition, respectively. Latest reports on phytochemical and therapeutic perspectives of C. majus extract recognize two alkaloidal compounds, 8-hydroxydihydrosanguinarine and 8-hydroxydihydrochelerythrine, which possess antibacterial effect against strain of Staphylococcus aureus. Moreover, sanguinarine and chelerythrine also show effective antibacterial activity against S. aureus, E. coli, and Aeromonas hydrophila ([Table 4]) ,.
|Table 4 Qualitative antimicrobial susceptibility tests estimated by samples|
Click here to view
| Conclusion|| |
UV irradiation can be successfully applied to enhance the color strength as well as color fastness properties of colored silk and flax fabrics by improving their wettability. The samples treated at 30 and 60 min of UV-irradiated for silk and flax, respectively, have the highest wettability. The dyeing condition (temperature and time) has been effected by the UV treatment, as the silk fabric is dyed at 30°C for 30 min whereas for flax was at 90°C for 60 min in alkaline media (pH 9). All the UV-irradiated samples had antimicrobial properties.
Industrial importance: physical treatment of silk fabric by UV radiation is a very promising method, as it can improve the color strength and fastness parameters without adding any mordant or salts at low dyeing bath temperatures for a short time period (saving energy) which could be applied for other dyes.
Financial support and sponsorship
Conflicts of interest
There are no conflicts of interest.
| References|| |
Yan Li, Chouw N, Jayaraman K. Flax fibre and its composites − a review. Composit B: Eng 2014; 56:296–317.
Coman D, Oancea S, Vrinceana N, Astoia M. Sonication and convetional dyeing procedures of flax fibres with Allium cepa
anthocyanin extract, cellulose. Chem Technol 2014; 48:145–157.
Mahapatra NN. Textile Dyes. India: CRC Press; 2016.
Singha AS, Kaith BS, Sarwade BD. Modification of flax fibre through graft copolymerization with methyl methacrylate and evaluation of swelling, moisture absorbance and thermal behavior. Hung J Ind Chem 2002; 30:289–291.
Hosseini M, Montazer M, Damerchely R. Enhancing dye-ability and antibacterial features of silk through pre-treatment with Chitosan. J Eng Fib Fabr 2013; 8:102–111.
Maji AK, Banerji P. Chelidonium majus
L. (Greater celandine) − a review on its phytochemical and therapeutic perspectives. Inter J Herbal Med 2015; 3:10–27.
Bhatti IA, Adeel S, Abbas M. Effect of Radiation on Textile Dyeing, Textile Dyeing, Prof. Peter Hauser (Ed.), 2011 InTech, DOI: 10.5772/19879. USA.
Iqbal J, Bhatti IA, Adeel S. Effect of UV radiation on dyeing of cotton fabric with extracts of henna leaves. Ind J Fib Text Res 2008; 33:157–162.
Bhatti IA, Adeelb S, Siddique S, Abbas M. Effect of UV radiation on the dyeing of cotton fabric with reactive blue 13. J Saud Chem Soc 2014; 18:606–609.
Judd DB, Wyszecki G. Color in business, science and industry. 3rd edition, USA: Wiley-Interscience; 1975.
ASTM Standard C33 (ASTM D1682-64 e1). Standard methods of test forbreaking load and elongation of textile fabrics. West Conshohocken, PA: ASTM International; 1975.
AATCC Test Method (8-1989), 68. (1993). Colorfastness to Crocking:AATCC CrockmeterMethod, Technical Manual Method of the American Association of Textile Chemistsand Colorists, USA.AATCC Test Method (15-1989), 68. (1993). Colorfastness to Perspiration, TechnicalManual Method of the American Association of Textile Chemists and Colorists, USA.AATCC Test Method (16A-1989), 68. (1993). Colorfastness to Light: Outdoor, TechnicalManual Method of the American Association of Textile Chemists and Colorists, USA.AATCC Test Method (36-1972), 68. (1993). Colorfastness to Washing: Characterizationof Textile Colorants, Technical Manual Method of the American Association of TextileChemists and Colorists, USA.
Adeel S. Influence of UV radiations on the extraction and dyeing of cotton fabric with Curcuma longa L. Ind J Fib Text Res 2012; 37:87–90.
Michael MN, El-Zaher NA. Investigation into the effect of UV/ozone treatment on the dyeing properties of natural dyes on natural fabrics. Colorage 2005; 52:83–88.
Herascu N, Simileanu M, Radvan R. Color changes in the in the art work materials aged by UV radiation. Rom Rep Phys 2008; 60:95–103.
Md MH, Nayem KA, Azim AYMA. Dyeing of cotton and silk fabric with purified natural curcumin dye. Int J Sci Eng Technol 2014; 3:838–844.
Sadeghi-Kiakhani M, Tayebi HA. Eco-friendly reactive dyeing of modified silk fabrics using corona discharge and chitosan pre-treatment. J Text Institute 2017; 108:1164–1172.
Lower ES. Chemicals and chemistry in the production and processing of silk. Halstead UK: The Silk Association of Great Britain Ltd; 1990.
El-Hennawi HM, Shahin AA, Rekaby M, Ragheb AA. Ink jet printing of bio-treated linen, polyester fabrics and their blend. Carbohydr Polym 2015; 118:235–241.
Adeel S, Rehman F, Gulzar T, Bhatti IA, Qaiser S, Abid A. Dyeing behavior of gamma irradiated cotton using Amaltas (Cassia fistula) Bark extracts. Asian J Chem 2013; 25:2739–2741.
Zuo GY, Meng FY, Hao XY, Zhang YL, Wang GC, Xu GL. Antibacterial alkaloids from Chelidonium majus
Linn (Papaveraceae) against clinical isolates of methicillin resistant Staphylococcus aureus
. J Pharm Pharm Sci 2008; 11:90–94.
Miao F, Yang XJ, Zhou L, Hu HJ, Zheng F, Ding XD. Structural modification of sanguinarine and chelerythrine and their antibacterial activity. Nat Prod Res 2011; 25:863–875.
[Figure 1], [Figure 2], [Figure 3], [Figure 4], [Figure 5], [Figure 6], [Figure 7], [Figure 8], [Figure 9]
[Table 1], [Table 2], [Table 3], [Table 4]